CM62026 Automatic AC High Voltage Withstand Tester
This equipment is designed and produced based on the GB standard, which is used in motors, transformers, cables, electrical appliances, insulation materials, high-voltage component manufacturers, as well as frequency voltage withstand test in high-voltage electricity laboratory of electric power, research center, colleges and universities, with low loss, light weight, less waveform distortion, and other advantages. The full set of devices consists of a high voltage test transformer, voltage regulators, and an integrated device of measurement, control and protection.
Category:
Product Introduction
1.Product Description
Automatic AC high voltage withstand tester is designed and produced based on the GB standard, which is used in motors, transformers, cables, electrical appliances, insulation materials, high-voltage component manufacturers, as well as frequency voltage withstand test in high-voltage electricity laboratory of electric power, research center, colleges and universities, with low loss, light weight, less waveform distortion, and other advantages. The full set of devices consists of a high voltage test transformer, voltage regulators, and an integrated device of measurement, control and protection.
NCM: 9030339000
2.Standard
- IEC 60060-1:1989
3.Technical Parameters
- Test Voltage: AC 10 kV
- Rated Capacity: 10 kVA
- Voltage Waveforms: Sine wave
- Voltage Error: ±3%
- Voltage Display Mode: Touch screens
- Unit Configuration: Console, voltage regulators, transformers
- Test Time: 0-600 s, settable
- Control Mode: Electric voltage boost
- Voltage Boost Mode: Auto boost, max voltage boost rate is 1000 V/S, after reaching 75% of the set value, the boost rate will be 2% per second
- Voltage Regulator: Auto type
- Transformer: Oil-immersed test transformer
- It is equipped with test lines and clip pliers, an alarm, and automatically returns when there is a wire failure.
- Overcurrent protection, during the test, a red warning light runs, at the end of the test, it stops automatically.
- Adopt intelligent LCD screen in the whole process, simple operation, greatly reduce test time, and improve the detection efficiency.
- This device's bottom is with corner wheels, freely movable, and lockable.
- Test Time Unit: Seconds
4.Specifications
- Overall Dimensions: 770 (L) × 770 (W) × 1280 (H) mm
- Power Supply: AC220V/ AC380V 50/60Hz
- Weight: About 200 kg
- High-voltage Lines and Ground Lines: User prepared
Keywords:
CM62026 Automatic AC High Voltage Withstand Tester
Related Machines
CM-FT1600 Φ1600mm Foundationless Traversing and Take-up Machine
Used for automatic cable take-up and orderly traversing on PN800–PN1600 reels with a loading capacity of ≤5T. It features electric lifting and lateral movement, foundation-free installation, and a maximum line speed of 110m/min, suitable for take-up applications in cable production lines
View More →
CM-BTM500 Φ500mm Vertical Back Twist Machine
Pre-twisting of insulated cores for Cat5e, Cat6 and higher category data cables.
View More →
CM-BCM500 Φ500 mm Bunching Machine
Applicable for stranding conductors or cores with seven or more wires, including tinned copper, bare copper, copper-clad aluminum (CCA), and copper-clad steel (CCS).
View More →
CM42149 Pressure Test Device at High Temperature
Pressure test device at high temperature is used in the indentation of the wire and cable insulation being produced at high temperature and pressure. To test the high temperature resistance and high pressure resistance deformation ability under thermal and mechanical loads simultaneously.
View More →Product Message
*Attention: Please ensure accurate information filling and maintain smooth communication. We will contact you as soon as possible
Email: info@cabmac.com
Tel: +86-519-88179989
Mobile: +86 13337881658
+86 18796986146
Address: 902-5, No.16 Longcang Road Tianning District, Changzhou, Jiangsu, 21300, China
Powered by: www.300.cn 丨 SEO 丨Privacy Policy