CM21003A Computer-controlled Servo-type Universal Tester
This equipment is used for tensile, compression, bending, cutting tests, which adopted with advanced machinery, SCM and computer technology to record the load of the sample, the variable displacement and time change curve, to research the material property and control the quality during manufacturing.
Category:
Product Introduction
1. Product Description
Computer-controlled servo-type universal tester (double columns) is used for tensile, compression, bending, cutting tests, which adopted with advanced machinery, SCM and computer technology to record the load of the sample, the variable displacement and time change curve, to research the material property and control the quality during manufacturing.
MCN: 9024101000
2.Standard
- ISO 6892-1:2009
- ISO 7500-1:2004
3.Technical Parameter
- Max Test Force: 5 KN
- Effective Stroke: about 800 mm
- Testing Width: 400 mm
- Test Force Value Relative Error: ≤±1%
- Sensor: American Transcell load cell
- Test Speed Range: 0.01-300 mm/min
- Displacement Resolution: 0.01 mm
- Support Beam: High carbon steel forged, good mechanical performance, without deformation
- Power System: Japan Panasonic 750 W servo motor
- Ball Screw: TBI2505 ball screw made in Taiwan, high transmission accuracy, using grinding process, good finish, keeping good accuracy, long service life. Good process of nuts, high load carrying capacity.
- Grip Surface Process: All of the grips are adopted the hard chromium plating process, the grip block is adopted imported Japanese tool steel, SKD-11 high frequency process, HRC is over 55, wear resistant and impact resistant.
- Guide Rod Bearing: NSK ball linear bearing imported from Japan
- Guide Rod: Made of two Ф30 bearing steels with surface hardening, the surface hardness can reach above HRC58
- Speed Reduce Device: AUTOS precision vacuum cast aluminum reducer 1: 20
- Dust Prevention Device: Taiwan suppression dust stacks cover to protect the screw from dust entry
- Machine Body Surface Treatment: Adopt the DuPont powder made in USA, electrostatic painting process, 200 ℃ high temperature curing, to ensure permanent non-fading.
- Display Method: Test software +computer display
- Section Bar: One-time extrusion, generous appearance. oxidation coloring aluminum alloy section bar, high hardness, abrasion and corrosion resistance.
- Auxiliary Remote control for clamps lifting.
- Safety Device: Overload stop function, up and down travel limiter, sample break stop function.
4.Specifications
- Overall Dimensions: 810mm×520mm×1850mm
- Power Supply: AC 220 V 50/60 Hz 5 A
Keywords:
CM21003A Computer-controlled Servo-type Universal Tester
Related Machines
CM42149 Pressure Test Device at High Temperature
Pressure test device at high temperature is used in the indentation of the wire and cable insulation being produced at high temperature and pressure. To test the high temperature resistance and high pressure resistance deformation ability under thermal and mechanical loads simultaneously.
View More →
This equipment is used in conjunction with the high-temperature oven, specimens are hung in the device and placed in an oven, and put the weights on the lower grip of specimens, after 10 minutes, measure the distance between the marks and calculate the elongation.
View More →
CM52160 Fluorine Content Measuring Instrument
The instrument is a perfect combination of advanced electronic technology, sensor technology, and software design, and is the most cost-effective laboratory fluoride concentration analysis instrument. It is widely used for the testing and analysis of fluoride in drinking water, surface water, seawater, domestic sewage, and industrial wastewater, as well as the determination of fluoride in mineral materials, organic materials, and biological materials.This instrument is built-in microprocessor chips, nice appearance, user-friendly with the following outstanding features.
View More →
CM52161 Halogen Acid Gas Release Determination Device
This equipment is used to measure gas volume of Halogen Acid (IEC 60754-1), pH concentration (PH Meter, Hydrogen ions, IEC 60754-2), Conductivity (IEC 60754-2) and etc from a wire (cable) by radiant heat in the Tube Furnace (IEC 60754-1: 800℃, IEC 60754-2: 950℃)
View More →Product Message
*Attention: Please ensure accurate information filling and maintain smooth communication. We will contact you as soon as possible
Email: info@cabmac.com
Tel: +86-519-88179989
Mobile: +86 13337881658
+86 18796986146
Address: 902-5, No.16 Longcang Road Tianning District, Changzhou, Jiangsu, 21300, China
Powered by: www.300.cn 丨 SEO