Tensile testing machine
Application: Testing tensile strength, elongation, torsion, and repeated bending of wires & cables.
Category:
Product Introduction
Application
Testing tensile strength, elongation, torsion, and repeated bending of wires & cables.
Features
Digital display, precision load cell, auto stop at break, IEC60811 compliant, high repeatability.
Technical parameters
| Type | CM-TTM Series |
| Max. test force | 5 kN, 10 kN, 20 kN (optional, selectable by customer) |
| Effective stroke | Approx. 800 mm |
| Testing width | 400 mm |
| Relative error of test force indication | ≤±1% |
| Load cell | Transcell load cell (USA) |
| Speed range | 0-300 mm/min |
| Displacement resolution | 0.01 mm |
| Large deformation measurement | Elongation is automatically tracked and calculated at the two gauge length points. |
| Large deformation resolution | 0.10% |
| Support crossbeam | High-carbon steel forging with excellent mechanical strength and no deformation. |
| Drive system | Panasonic servo motor, 750 W (Japan) |
| Ball screw | Taiwan TBI 2505 ball screw, featuring high transmission accuracy; manufactured by precision grinding process with excellent surface finish, good accuracy retention, and long service life. The nut is well engineered with high load-bearing capacity. |
| Metal fixtures | All fixtures are hard chrome plated. The clamping blocks are made of imported SKD-11 tool steel from Japan; after heat treatment, the hardness reaches HRC55 or above, featuring excellent wear resistance and impact resistance. |
| Rotating bearings | NSK deep groove ball bearings (Japan) |
| Guide rods | Two Φ30 bearing steel rods with surface hardening treatment; surface hardness up to HRC58 or above. |
| Reduction unit | OTIS precision vacuum die-cast aluminum gearbox, reduction ratio 1:20. |
| Dust protection device | Equipped with Taiwan telescopic dust cover to protect the screw and prevent dust ingress. |
| Surface treatment | DuPont powder coating (USA), electrostatic spraying process; cured at high temperature of 200 °C to ensure long-lasting color without fading. |
| Display method | Testing software with computer display. |
| Machine frame | One-piece extruded aluminum alloy profiles, featuring high strength, low deformation, and excellent corrosion resistance. |
| Fixture lifting | Equipped with an auxiliary remote controller for fixture lifting. |
| Safety devices | Overload protection with automatic shutdown, upper and lower travel limit switches, and specimen break protection with automatic stop. |
Keywords:
Tensile testing machine
Related Machines
CM-FT1600 Φ1600mm Foundationless Traversing and Take-up Machine
Used for automatic cable take-up and orderly traversing on PN800–PN1600 reels with a loading capacity of ≤5T. It features electric lifting and lateral movement, foundation-free installation, and a maximum line speed of 110m/min, suitable for take-up applications in cable production lines
View More →
CM-BTM500 Φ500mm Vertical Back Twist Machine
Pre-twisting of insulated cores for Cat5e, Cat6 and higher category data cables.
View More →
CM-BCM500 Φ500 mm Bunching Machine
Applicable for stranding conductors or cores with seven or more wires, including tinned copper, bare copper, copper-clad aluminum (CCA), and copper-clad steel (CCS).
View More →
CM42149 Pressure Test Device at High Temperature
Pressure test device at high temperature is used in the indentation of the wire and cable insulation being produced at high temperature and pressure. To test the high temperature resistance and high pressure resistance deformation ability under thermal and mechanical loads simultaneously.
View More →Product Message
*Attention: Please ensure accurate information filling and maintain smooth communication. We will contact you as soon as possible
Email: info@cabmac.com
Tel: +86-519-88179989
Mobile: +86 13337881658
+86 18796986146
Address: 902-5, No.16 Longcang Road Tianning District, Changzhou, Jiangsu, 21300, China
Powered by: www.300.cn 丨 SEO